Topsoil Calculator
Cubic yards, tons and bags of topsoil for a lawn or garden bed.
Penn State Extension says new turf needs at least 4 to 6 inches of topsoil once it has settled.
Covers settling. Fresh topsoil settles after it is spread.
Use the figure from your supplier. It changes with the material and how wet it is, so there is no default.
The volume is printed on the bag.
Examples: , ,
Enter length, width and depth to see how much topsoil you need.
Short answer
Multiply the area by the depth of the layer, both in feet, to get cubic feet. Add extra for settling, then divide by 27 for cubic yards. For a new lawn, Penn State Extension says to plan on at least 4 to 6 inches of topsoil, measured after it settles.
On this page
How do I use the topsoil calculator?
- Pick a shape: Known area for a lawn you already measured, Rectangle for a raised bed, or Circle for a round bed. The square footage calculator finds the area of an odd shape.
- Enter the measurements and the depth.
- Keep the extra at 10%, or change it.
- Read the cubic yards. For tons, type the weight per cubic yard your supplier gives you. For bags, type the bag size from the label.
How is the volume worked out?
Topsoil is a volume: the area times the depth of the layer. The extra covers settling, because fresh soil sinks after it is spread.
- Area of a rectangleArea = L × W
- Area of a circleArea = π × (D ÷ 2)²
- VolumeV = Area × d
- Total with extraTotal = V × (1 + x ÷ 100)
- WeightWeight = Total × p
- BagsBags = round up (Total ÷ B)
Round up means to the next whole number. Weight and bags show only when you enter p or B.
| Symbol | Meaning | Unit |
|---|---|---|
| L | Length of the bed | ft (m) |
| W | Width of the bed | ft (m) |
| D | Diameter of a round bed | ft (m) |
| d | Depth of the layer | in (cm) |
| x | Extra for settling | % |
| p | Weight per volume, from your supplier | tons/yd³ (t/m³) |
| B | Volume of one bag, from the label | ft³ (L) |
Worked example
A lawn of 1,000 square feet with a 4 inch layer and the default 10% extra.
| Shape | Known area |
|---|---|
| Area | 1,000 ft² |
| Depth | 4" |
| Extra for waste | 10% |
| Topsoil needed | 13.58 yd³ |
|---|---|
| Without extra | 12.35 yd³ |
A common mistake
Entering the final depth instead of the depth you are adding. If the bed already has soil and you are topping it up, the depth to type is the new layer only. Entering the total depth of the finished bed makes the result larger than the soil you need to buy.
How far does a cubic yard go?
Depth changes the order a lot. This table is plain arithmetic, so you can check the calculator against it. A second table lists the cubic yards for lawns of common sizes, with 10% extra.
| Depth | 1 yd³ covers | 100 ft² takes |
|---|---|---|
| 2 in | 162 ft² | 0.62 yd³ |
| 4 in | 81 ft² | 1.23 yd³ |
| 6 in | 54 ft² | 1.85 yd³ |
| 8 in | 41 ft² | 2.47 yd³ |
| Lawn area | 4 in deep | 6 in deep |
|---|---|---|
| 500 ft² | 6.79 yd³ | 10.19 yd³ |
| 1,000 ft² | 13.58 yd³ | 20.37 yd³ |
| 2,000 ft² | 27.16 yd³ | 40.74 yd³ |
| 5,000 ft² | 67.90 yd³ | 101.85 yd³ |
How deep should topsoil be?
For a new lawn, Penn State Extension says a minimum of 4 to 6 inches of good topsoil is typically needed, measured at its firmed or settled depth. Because the soil sinks as it settles, the layer you spread should be a little thicker than the depth you want in the end. The extra field is there for that.
The same source adds that 2 inches of the topsoil should ideally be mixed into the upper 2 to 3 inches of the subsoil, so there is a gradual change between the two layers.
| What | Depth |
|---|---|
| Minimum, firmed or settled | 4 to 6 in (10.2 to 15.2 cm) |
| Mixed into the subsoil | 2 in (5.1 cm) |
Lower the subgrade first
Penn State says the subsoil grade should be lowered to make room for the added topsoil. Plan for that before you order.
How do I order topsoil by the ton or by the bag?
Bulk topsoil is usually sold by the cubic yard, and sometimes by the ton. To change cubic yards into tons you need your supplier's weight per cubic yard. There is no default, because it changes with the soil and with how wet it is.
Bags are for small beds. The volume of each bag is printed on it. The calculator divides your total volume by the bag volume and rounds up.
| Step | Result |
|---|---|
| Volume with extra | 13.58 yd³ |
| Weight at 1.2 tons/yd³ | 16.30 tons |
Frequently asked questions
How much topsoil do I need for a new lawn?
Penn State Extension says a new lawn typically needs a minimum of 4 to 6 inches of good topsoil, measured after it has firmed or settled. Multiply your area by that depth in feet, divide by 27 for cubic yards, and add extra for settling. For 1,000 square feet at 4 inches, that is 12.35 cubic yards before any extra.
How many cubic yards of topsoil is a ton?
It depends on the soil. Weight per cubic yard changes with the mix and how wet it is, so Snapline does not guess. Ask your supplier for the figure, enter it in the weight field, and the calculator multiplies it by your volume.
Do I need extra topsoil for settling?
Yes, a little. Fresh topsoil settles after it is spread, so the layer ends up thinner than the one you measured. We start at 10%, our default and not a standard, and you can set anything from 0% to 25%.
Related calculators
- Mulch CalculatorCubic yards and bags of mulch for beds, borders and tree rings.
- Gravel CalculatorCubic yards, tons and bags of gravel for a path, driveway or base.
- Square Footage CalculatorArea of a rectangle, circle, triangle or trapezoid, in square feet, yards and meters.
- Retaining Wall CalculatorBlocks, caps and gravel for a segmental retaining wall.